When a landlord in Cedar Hill gets a call about a dead outlet in a rental unit, or a contractor finishing a home addition needs the electrical signed off before drywall goes up, the call comes to us. Wesson Electrical Services handles those jobs alongside the full range of residential electrical work that a city this size generates every day. A home that has been renovated in stages, a garage that needs power for the first time, a panel that trips under load every summer: these are the calls we take and the problems we solve.
Property managers and builders are not the only ones who call. Homeowners dealing with an aging system, a new appliance that needs its own circuit, or a safety concern that showed up during a renovation are just as likely to be on the line. Whoever is calling, the process is the same: describe the job, get a price on the phone, and schedule a visit. Licensed electricians handle the work, and we are open every day from 6:00 AM to 10:30 PM.
Getting your electrical problem handled starts with a quick call. Same-day appointments are often available, and for situations that cannot be left overnight, we do our best to get someone out that day. A burning smell near a panel, a breaker that will not reset, or a partial power loss that has taken out a whole section of the house are not problems to schedule for next week.
For tenants, we work around the fact that someone lives in the property. For businesses that need to stay open, we can often sequence the work to keep the affected area as small as possible. The goal is to solve the problem with as little disruption as the job allows.
We know schedules shift, so we keep booking flexible, and that applies to landlords coordinating access with a tenant as much as it does to homeowners trying to stay out of a contractor's way. Call us, tell us what is going on, and we will work out a time that fits.
The price for electrical work depends on what the job actually involves, and the only honest quote is one that comes after you have described the work. When you call, we go through the job with you and give you a rate on the phone before anything is scheduled. The price is confirmed before we send anyone out.
What changes a quote is usually scope: a repair that looks straightforward can turn out to involve wiring that needs to be corrected before the repair can be completed, or a panel that needs more work than the original circuit addition suggested. If we find something during the visit that changes the scope, we discuss it with you before the work continues. Nothing is added without your agreement.
Electrical work done to the standard the next inspection expects is the baseline for every job. That sometimes means a quote covers more than the immediate symptom, because fixing the symptom on top of a code problem is not a fix that holds. Ask what the price covers and you will get a straight answer.
Cedar Hill has a range of housing, from newer builds to homes that have been added onto over the years in ways that were not always documented. The electrical work those properties generate is not uniform, and a call about a tripping breaker in a house from one era is a different job from the same complaint in a house from another.
A fault that shows up as a flickering light or a dead outlet can have its source anywhere along the circuit, from a loose connection at the device to a failing breaker at the panel. We trace the fault rather than guess at it. That means testing the circuit from both ends and working out where the problem actually is before anything is replaced. Clear communication from the first call to the final test is how every repair runs.
A panel that was sized for an earlier version of the house is a common situation in a city where homes have been expanded and updated over time. When the load has grown beyond what the original service can carry, or when a new appliance or EV charger needs a circuit the panel cannot support, a service upgrade is the right answer. We handle load calculations, full panel replacements, and subpanel additions for outbuildings or additions. If the service entrance itself needs upgrading to bring the meter and incoming supply in line with the new panel, that is part of the same conversation.
New circuits, outlet additions, lighting installations, ceiling fan replacements, and outdoor wiring all fall under installation work, and each one starts with a look at what the panel can support. A dedicated circuit for a dryer or a workshop tool is a different scope from a whole-home rewiring, but both start from the same question: what does the system actually need to handle this load safely? The service page carries the full breakdown of what we install and how each type of job runs.
Apartments and flats have their own wrinkle: the panel for an individual unit is often in a shared corridor, a utility room, or a basement space that is not inside the unit itself. That affects access, and it sometimes affects who is responsible for the work.
Outlets, switches, lighting, and the circuits feeding them are typically the tenant's or owner's side of the system. GFCI and AFCI protection, arc-fault and ground-fault breakers, and any wiring within the unit walls fall here. These are the parts we can inspect and repair on a standard visit.
The incoming supply, the meter, and any shared distribution equipment are usually the building owner's or the utility's responsibility. If a fault traces back to that side of the system, we will tell you clearly and point you toward who to contact. We do not guess at what is shared and what is not.
A home that was wired for a certain load and then asked to run a fast EV charger, a hot tub, a workshop full of power tools, and a modern kitchen on top of the original appliances is asking more than the system was designed to give. Whether it can handle that depends on the panel capacity, the condition of the existing wiring, and whether the circuits feeding the new loads are sized correctly.
We work out the actual load before we run any new circuit. If the panel has room, we add the circuit. If it does not, we talk through the options: a panel upgrade, a subpanel for the new loads, or a phased approach that prioritizes what matters most. Aluminum-wiring remediation comes up in this conversation too, because older homes that were wired with aluminum branch circuits need that addressed before adding load. Work in this area gets done to the code inspectors here actually enforce, and that shapes how we scope every addition.
An inspection gives you a clear picture of where the system stands. Pre-purchase inspections are common when a buyer wants to know what they are taking on. Landlords use them for compliance documentation. Homeowners use them when the wiring is old or when previous work raises questions. We produce a written report of what we find and what it means, so you can decide what to address and in what order.
Rewiring is the right answer when the existing wiring is deteriorated, does not meet current code, or cannot safely carry the loads the house now needs. Partial rewiring covers the sections that need it most. Whole-home rewiring replaces everything from the panel to the devices. Either way, the result is code-compliant wiring throughout the affected areas and a system that will pass inspection.
A ceiling fan installation is straightforward when the wiring is already there and more involved when it is not. Older boxes that were not rated for a fan's weight, circuits that were not designed to carry a fan and a light together, and rooms that have never had a ceiling fixture all come up. We handle the wiring and the mounting, not just the fixture swap.
Grounding and bonding problems show up on inspection reports and in situations where GFCI protection is required but the circuit has no ground. We correct grounding at the panel and at individual circuits, and we handle bonding for metal piping, gas lines, and structural elements where the code requires it.
Running power to a structure that is separate from the main house involves its own set of requirements: the right conduit, a properly sized circuit, grounding at the subpanel or disconnect, and weatherproof materials throughout. Electric gate operators add a control circuit on top of the power supply. We handle the full run from the main panel to the outbuilding.
A new appliance that draws significant power needs its own dedicated circuit. A hot tub needs a 240-volt supply with a disconnect within sight of the unit. Workshop equipment with high-draw motors needs circuits sized for the starting load, not just the running load. We assess what each piece of equipment needs and run the circuit to match.
our page on electrical repairs sets out the options.
We cover Cedar Hill and the surrounding Dallas County area, and that includes Duncanville, DeSoto, Glenn Heights, Ovilla, and Grand Prairie. If your property is in one of these communities, the process is the same: call for a quote, get a price on the phone, and schedule when it works for you.
Dallas County has a wide range of housing and commercial properties, and we handle electrical work across all of it. If you are not sure whether your address falls within our area, call and we will confirm right away.
Yes. If the panel directory is missing, incomplete, or wrong, we can trace and label every circuit so the directory reflects what is actually there. This is useful for older properties where circuits have been added over time without being documented. It is also a good starting point before any major electrical work.
A car lift and similar shop equipment typically runs on 240 volts and draws significant current, so it needs a dedicated circuit sized for the motor load. We calculate what the equipment requires, run the dedicated circuit from the panel, and install the right outlet or connection point. If the panel needs additional capacity to support the load, that is part of the conversation before the job is booked.
In most cases, the main power to the house needs to be off during the critical part of a panel replacement or service upgrade. We tell you in advance which circuits will be affected and for how long, so you can plan around it. For smaller jobs that only affect one circuit, the rest of the house typically stays live.
If we find wiring or a previous installation that raises a safety concern, we stop and explain what we found before doing anything else. You decide how to proceed. We do not continue work over a known hazard without your understanding of what it means and what it takes to correct it.
We can help identify where the fault is. If the problem is between the meter and the house, or at the service entrance, we let you know and explain what the utility's role is in addressing it. We do not work on the utility's equipment, but we can tell you what you are dealing with and what the next step looks like.
Labeling the panel is part of finishing the job correctly. If breakers are unlabeled or mislabeled when we arrive, we update the directory as part of the work. A panel that is accurately labeled makes future troubleshooting faster and helps anyone who needs to shut off a specific circuit quickly.
Yes, we work with landlords and property managers on rental properties throughout the area. The process is the same as any other job: describe the work, get a price on the phone, and schedule access with the tenant. We can coordinate timing to minimize disruption, and we document the work clearly for your records.
Yes. When the property has a tenant in place, we work with the scheduling details you provide and confirm the appointment window so the tenant knows when to expect the electrician. We coordinate through you or the property manager rather than working directly around the tenant's schedule without your involvement.
In many cases, yes. We can prioritize the areas of greatest concern, such as a kitchen or a room with the worst wiring condition, and return for additional phases as your schedule and budget allow. The approach depends on how the existing wiring is laid out and whether partial completion leaves the system in a safe and functional state. We walk through the options with you before committing to a plan.
We start with a diagnostic visit and trace what is there rather than assuming the system matches what is labeled or what the original plans show. Homes that have been added onto in stages often have wiring from more than one era, and we work through it methodically before recommending any repair or upgrade. We explain what we find before any work begins.
Wesson Electrical Services takes calls every day from 6:00 AM to 10:30 PM. When you call, you reach someone who can talk through the job, give you a rate, and get a visit on the calendar. The electrician who shows up explains what they find before any work begins. We answer the phone. We dispatch the electrician. We keep it simple.
Call (945) 429-1659 for a quote on electrical work in Cedar Hill.
Also serving: DeSoto, Lancaster, Waxahachie. Browse our service area.
Below is a plain-language look at the electrical services we handle for homes and businesses in Cedar Hill and across Dallas County. Each row covers what the work involves, who it fits best, and one practical thing worth knowing before you call. If you have questions about a specific job or want a quote, call us any day from 6:00 AM to 10:30 PM.
| Electrical Service | What the Job Involves | Ideal For | Worth Knowing |
|---|---|---|---|
| Electrical Safety Inspections | pre-purchase and pre-sale inspectionsrental property compliance inspectionsolder-home wiring assessments | Buyers, sellers, and landlords who need a clear picture of where a property's electrical system stands | If the inspection turns up code violations or safety concerns, we can handle the repairs as a follow-up and provide the documentation an inspection or claim may require. |
| Wiring for Additions & Remodels | kitchen and bathroom circuit workaddition wiringcontractor coordinationcode compliance documentation | Homeowners mid-renovation who need electrical roughed in before walls close | Remodel work often uncovers older wiring that needs to be brought up to current standards before the inspection. We handle both the new work and the corrections. |
| Basement & Sump-Pump Circuits | dedicated sump-pump circuitbasement outlet installationGFCI protection in wet areas | Homeowners finishing a basement or ensuring a sump pump has its own reliable circuit | A sump pump on a shared circuit can lose power at the worst moment. A dedicated circuit with GFCI protection is the right setup. |
| Outlet & Switch Installation | standard and GFCI outlet replacementAFCI outletsdimmer and smart switches240-volt outlets | Homeowners adding outlets, updating older receptacles, or upgrading to GFCI protection in kitchens and baths | GFCI outlets can be installed on ungrounded circuits and still provide shock protection where a ground wire is not present. |
| Breaker & Fuse Repair | tripped or worn breaker replacementfuse box evaluationpanel breaker testing | Homeowners whose breakers trip repeatedly or whose fuse box has never been updated | A breaker that trips under normal load is signaling a problem, not just doing its job. It is worth diagnosing rather than resetting. |
| Electrical Panel Upgrades | 200-amp service upgradesfull panel replacementsubpanel installationload calculations | Homes with outdated or undersized panels, or any property adding an EV charger, major appliance, or generator | Many Dallas County homes are still running panels sized for loads from a different era. A panel assessment is the right starting point if breakers trip often or capacity feels tight. |
| Ceiling Fan Installation | fan mounting and wiringswitch and remote setupnew ceiling box installation | Homeowners replacing an existing fan or adding one where no fixture exists | If there is no existing ceiling box rated for a fan, we install one before mounting. Skipping that step is a safety issue. |
| Wiring & Circuit Installation | new circuit runscircuit extensionsdedicated appliance circuitsoutdoor and weatherproof wiring | Homes or businesses that need power in a new location or additional circuits for added load | Adding circuits without checking panel capacity first can create an overload situation. We assess capacity before running any new wire. |
| Whole-Home Surge Protection | panel-level surge device installationprotection for appliances and electronicspost-storm follow-up installation | Any North Texas home exposed to thunderstorm surge risk, especially after a panel upgrade or a prior surge event | A whole-home surge protector at the panel covers every circuit at once. A power strip only protects what is plugged into it. |
| Older-Home Rewiring | knob-and-tube removalaluminum branch-circuit remediationpartial or whole-home rewire | Owners of older Dallas County homes with wiring that was never designed for modern electrical loads | Aluminum branch-circuit wiring and knob-and-tube are not just outdated. They carry real safety and insurance implications. We explain the options before any work begins. |
| Electrical Repairs & Troubleshooting | fault diagnosiscircuit testingburned or loose connectionsrestoring lost power | Any home or business with flickering lights, dead outlets, or unexplained power loss | A burning smell or sparking outlet is a safety issue. Call the same day rather than waiting. |
| Lighting Installation | recessed and LED lightingsecurity and motion sensor lightslandscape lightingexterior fixture installation | Homeowners upgrading indoor lighting or adding outdoor security and accent lighting | Outdoor fixtures installed in North Texas need to be rated for heat and moisture exposure. That is a code requirement, not just a recommendation. |
| Backup Generator Installation | transfer switch installationstandby generator wiringcircuit hookup for critical loads | Cedar Hill homeowners who have experienced extended outages during storm season and want reliable backup power | The transfer switch is the critical piece. It isolates your home from the utility grid so the generator can run safely without back-feeding the line. |
| Dedicated Appliance Circuits | dryer and range circuitsrefrigerator and dishwasher circuitsworkshop and garage circuits | Homeowners adding high-draw appliances or experiencing repeated tripping on shared circuits | Most major appliances require their own dedicated circuit by code. Sharing a circuit with other loads shortens equipment life and trips breakers. |
| EV Charger Installation | dedicated 240-volt circuitLevel 2 charger installationpanel capacity assessment | Electric vehicle owners who want faster overnight charging than a standard 120-volt outlet provides | If the panel does not have the capacity to support a Level 2 charger, we handle the upgrade as part of the same project. |
If you have questions about a specific job or want to talk through what your home or property needs, call us at (945) 429-1659 any day from 6:00 AM to 10:30 PM and we will give you a straight answer.
(945) 429-1659